EuroBinBox                                
BinLocImage


•Tough, durable aesthetic screen that can hold and secure commercial
wheelie bins from 660 ltrs to 1100 ltrs.
•Registered design ensures quality and continuity of supply.
•Can be supplied and fitted on site, simple modular construction and
flat pack design, means it is not difficult to erect and install.
* Visually affective in hiding unsightly bins and comes with
compartments for multi bin occupancy.
•Rotating bar lock ensures the bin is secured in its own bay.
•Complies with CFPA (Europe) requirements for the siting of multiple
bins near buildings. Provides 30 mi. .Insulation & integrity
•Keeps communal and commercial areas neat and tidy as well as hiding the bins.
•EurobinBox must be fitted to a solid base such as paving flags, concrete or asphalt.
•Because of its simple modular design and assembly, if a panel becomes
damaged, a replacement section can be provided.
•Apart from the ‘Box Hedge’. Design, The EuroBinBox can be
supplied with bespoke coverings.
•EuroBinBoxes are designed to require the very minimum in maintenance.
A periodic wife down is all that’s needed to keep them clean.
•If the centre panel suffers minor damage it can be touched up using our
MultiKote paint.



Bin Loc Image Small  Bin Loc Image 2 small Bin Loc Small 3 
To see the ranges of bin box View the Ranges tab below.
Every Bin Loc is made to order. To order or find out more please contact us.







  • Description
  • Specifications
EuroBinBox is a visually impressive means of both hiding unsightly wheelie bins and securing them with the patented BinLoc BP. Binboxes provide a semi enclosed module that can hold multiples of two wheelie bins at one time. Binboxes will accommodate all sizes of external domestic wheelie bin, including the large 360 Ltr. They meet the requirements of both EU and local fire service recommendations to secure bins away from homes. Made from durable fabricated steel and structural OSB, the EuroBinBox comes in modular form and can be easily assembled on site. Because of its modular construction it can easily be extended or reduced, or damaged panels can simply be replaced by new ones. Oasis EuroBinBoxes can be used on a temporary or permanent basis, as required

The frame is made up of 40 mm x 40 mm x 3 mm m/s box section hot dipped galvanised to Bs 729 & ISO 1469. There is a left and right hand ‘H’ frame to hold the side panels. There is also a centre ‘H’ fame to hold an infill panel.
• The side frames and/or centre frames are connected to a 20 x 40 x 1.5 mm pre galvanised strut onto wich is bolted the rear panel.
• At the foot of each frame is a 100 mm x 100 mm x 4 mm m/s galvanised plate with 4 pre drilled holes at 80 mm centre.
• For fixing to a solid base of heavy duty paving flags, concrete or asphalt, an M6 thunderbolt is drilled in and tightened up.
• The side panel is made up of treated 1100 mm x 1400 mm x 11 mm OSB 3 board to BBA 08/4546with pre drilled M8 4 pronged ‘T’ nuts. The internal face of the OSB3 board is covered with pre galvanised expanded metal sheeting to Bs 405 and ISO 14001. The external face of the OSB3 board is covered, by mechanical fixings a 38 mm synthetic grass covering or Vinyl covering to bespoke design.
• The rear panel is made up of treated 1400 mm x 1500 mm x 11 mm OSB 3 board to BBA 08/4546with pre drilled M8 4 pronged ‘T’ nuts. The internal face of the OSB3 board is covered with pre galvanised expanded metal sheeting to Bs 405 and ISO 14001. The external face of the OSB3 board is covered, by mechanical fixings a 38 mmsymthetic grass covering or Vinyl covering to bespoke design.
• The centre infil panels made up from treated OSB3 board and fits tight within the angled section of the ‘H’ frame and secured with bullet head bolts and nuts.
• On the end and side panels a swing arm locking mechanism is provided secured in the open and closed position with a bullet lock.
• A kick board is fitted to the exterior base of the side and rear panels on the grass design.
• Once the rear board is tightened, a plastic cap is fitted to the strut channel.

The frame is made up of 40mm x 40mm x 3mm m/s box section hot dipped galvanised to Bs 729 & ISO 1469. There is a left and right hand 'H' frame to hold the side panels. There is also a center 'H' frame to hold an infill panel.

The side frames and center frame are connected to a 20 x 40 x 1.5 mm pre galvanised strut onto which is bolted the rear panel.

At the foot of each frame is a 100mm x 100mm x 4mm m/s galvanised plate with 4 pre drilled holes at 80mm center.

For fixing to a solid base of heavy duty paving flags, concrete or asphalt, an m6 thunderbolt is drilled in and secured up.

The side panel is made up of treated 1100mm x 1400 mm x 11mm OSB 3 board to BBA 08/4546 with pre drilled M8 4 pronged 'T' nuts. The internal face of the OSB3 board is covered with pre galvanised expanded metal sheeting to Bs 405 and ISO 14001. The external face of the OSB3 board is covered by mechanical fixings a 38 mm synthetic grass covering or vinyl covering to bespoke design.

The center infill panels made up from treated OSB3 board and fits tight within the angled section of the 'H' frame and secured with bullet head bolts and nuts.

On the end and side panels a swing arm locking mechanism is provided secured in the open and closed position with a bullet lock.

A kick board is fitted to the exterior base of the side and rear panels on the grass design.

Once the rear board is tightened, a plastic cap is fitted to the strut channel.