Eco Bin Box                                                   
BinLocImage


•Registered design ensures quality and continuity of supply
•Simple modular construction enables easy assembly on site,
supplied as a flat pack and bolted together
•Standard dimensions. 800 mm deep and 1600 mm wide,
to hold 2 wheelie bins (up to 360 ltrs.)
• Robust construction means its virtually vandal proof.
• Bin can be locked inside, with extra supplied OasisBinLoc back plate.
• Can be situated within a garden or communal area.
• Complies with current fire regulations and should be sited 2 mtrs from a building.
• Removes the condition of ‘bin blight, where wheelie bins are strewn about and around in front of homes, blocking pavements etc.
• Transforms neighbourhoods by providing a tough, durable, good looking and low maintenance solution to waste storage.
• Must be fixed to a solid base; paving flags, concrete or asphalt.(See fixings sheet)
• The simpleness of the construction and assembly means the unit copes well with general wear and tear. However, if a panel should get damaged it can easily be replaced without dismantling the whole unit.
• All parts can be ordered separately..


Bin Loc Image Small  Bin Loc Image 2 small Bin Loc Small 3 
To see the ranges of bin box View the Ranges tab below.
Every Bin Loc is made to order. To order or find out more please contact us.







  • Specification
  • Description
* Frame consisting of 40mm x 40 mm x 1100 mm x 2.5 mm strut channels, galvanised to Bs.729 & ISO 1469. Attached to 1100 mm x 800 mm assembled side panel.
* Rear assembled panel is attached to the struts on the side panel with M8 button head bolts into 4 pronged T nuts within the panel.
* In areas of high vandalism, and the high risk of fire, both side and rear panels can have 7.62 SW bonded expanding metal sheet to Bs405 and EN ISO 14001.
* The side panel (1100 mm x 800 mm x 13 mm)assembly shall be treated Oriented Strand Board (11 mm) 3; to BBA 08/4546 and ASTM-E119, unto which is fixed a covering of 38 mm synthetic grass or a covering of choice (outside)
* Internally, a 40 mm x 10 mm x 2. Mm pre galvanised m/s edging trim fixed to the OSB 3 and securing the grass (or external covering)The strut channel is fixed over the edging plate and bolted to the OSB 3
* The rear panel (1600 mm x 1100 mm x 13 mm) assembly shall be treated OSB 3 onto which is fixed an external covering of synthetic grass (or similar). An edging strip of 40 mm x 10 mm x 2.5 mm pre galvanised edging trim is fixed to the OSB securing the grass (or external covering, in place.
* If required the BinLoc back plate can be fitted to the internal face of the rear panel to secure the wheelie bins.
* On the grass finish a treated kick board is supplied, to be fixed on the bottom of the external face of the rear panel.
* It is recommended that the inside of the EcoBinBox unit be cleaned down periodically and if necessary and the OSB coating can be touched up if damaged

EcoBinBox is a visually impressive means of both hiding unsightly wheelie bins and securing them with the patented BinLoc BP. 

EcoBinBoxes provide a semi enclosed module that can hold multiples of two wheelie bins at one time. Binboxes will accommodate all sizes of external domestic wheelie bin, including the large 360 Ltr. They meet the requirements of both EU and local fire service recommendations to secure bins away from homes.

Made from durable fabricated steel and structural OSB, the BinBox comes in modular form and can be easily assembled on site. Because of its modular construction it can easily be extended or reduced, or damaged panels can simply be replaced by new ones.
Oasis BinBoxes can be used on a temporary or permanent basis, as required.
Frame consisting of 40mm x 40mm x 1100mm x 2.5mm strut channels, galvanised to Bs.729 & ISO 1469. Attached to a 1100mm x 800mm assembled side panel.

Rear assembled panel is attached to the struts on the side panel with M8 button head bolts into a 4 pronged T nuts within the panel.

In areas of high vandalism and the high risk of fire, both the side and rea panels can have 7.62 SW bonded expanding mental sheet to Bs405 and EN ISO 14001.

The side panel (1100mm x 800mm x 13mm) assembly shall be treated with oriented Strand board (11mm) 3; to BBA 08/4546 and ASTM-E119, unto which is fixed a covering of 38mm synthetic grass or a covering of choice (outside)

Internally, a 40mm x 10mm x2 mm pre galvanised m/s edging trim fixed to the OSB 3 and securing the grass (or external covering) the strut channel is fixed over the edging plate and bolted to the OSB3

The rear panel (1600mm x 1100mm x 13mm) assembly shall be treated OSB 3 onto which is fixed an external covering of synthetic grass (or similar). An edging strip of 40mm x 10mm x 2.5mm pre galvanised edging trim is fixed to the OSB securing the grass (or external covering) in place.

If required the BinLoc back plate can be fitted to the internal face of the rear panel to secure the wheelie bins.

On the grass finish a treated kick board is supplied to be fixed at the bottom of the external face of the rear panel.

It is highly recommended that the inside of the EcoBinBox unit be cleaned down periodically and if necessary and the OSB coating can be touched up if damaged with out MultiKote paint.

All cracked broke or bent panels/struts can be replaced

The fitting of the EcoBinBox must be to a solid base either paving concrete or asphalt. (See dimensions for fitting in our design section)